FIVER FIVER AUTOPARTS CO.,LTD — Chongqing

FIVER AUTOPARTS CO.,LTD

Electric Compressors and Heat Pumps: The New Core of EV Thermal Management

EVs need electric compressors, and heat pumps can cut winter range loss dramatically. A guide to refrigerants, lubrication, NVH and high-voltage service safety.

Why an EV cannot use a belt-driven compressor

In a combustion-engine car, the air-conditioning compressor is normally driven by an accessory belt, so cooling is available whenever the engine runs. A battery-electric vehicle has no engine at the front of that belt, so the compressor must carry its own electric motor and controller. Manufacturers describe semi-hermetic scroll electric compressors that can both cool and act as a heat pump, and newer high-voltage designs operating from roughly 120 V to 340 V DC (Sanden electrical compressors). DENSO notes that its electric-driven scroll compressors, used in hybrid and electric vehicles, require a POE oil because the electric motor is cooled by the refrigerant and oil mixture (DENSO compressor oil). The Mobile Air Climate Systems Association describes the service reality: electric compressor design, three-phase motor operation and electronic compressor control (MACS 609 training).

Cabin heating is where range disappears

Heating and cooling are not side issues in an EV. A U.S. Department of Energy study published through OSTI found that managing cabin climate control and battery temperature can increase energy demand by more than 50%, severely limiting range (DOE OSTI EV thermal study). The same study compared three vehicles at -7 degrees C: the Nissan Leaf Plus, which uses a heat pump with a PTC heater for the cabin, lost 19.3% of range, while the Tesla Model 3 and Chevrolet Bolt, which rely on PTC heaters, lost 28.3% and 31% respectively (DOE OSTI EV thermal study). At 35 degrees C, air-conditioning alone reduced range by 8%, 9% and 13% in the three vehicles (DOE OSTI EV thermal study).

The physics explains the gap. A positive-temperature-coefficient (PTC) heater generates heat directly from electricity, whereas a heat pump moves heat from the outside air into the cabin, which is why the heat-pump vehicle kept more range in that test (DOE OSTI EV thermal study). A heat-pump-capable system also needs more than a reversing valve: it typically adds an electronically controlled expansion device, extra heat exchangers and a controller that decides when to use the heat pump, a PTC booster or waste heat, and that control logic is where much of the real-world efficiency difference is won or lost (our analysis). The engineering trend is to go further: the UTEMPRA project integrated the thermal management of electric-drive subsystems into a single system with heat-pump operation and waste-heat recovery, aiming to reduce auxiliary loads and increase range (DOE OSTI UTEMPRA).

Refrigerant choices: R1234yf, R290 and R744

The refrigerant decision is now part of the thermal architecture. The EPA lists HFO-1234yf at a GWP of 4, mildly flammable and classified ASHRAE A2L, and R-744 (CO2) at a GWP of 1 but operating at 5 to 10 times the pressure of other MVAC systems (EPA refrigerant data). R-744 is accepted for new vehicles only and, although exempt from the Section 608 venting prohibition, it remains subject to Section 609 servicing requirements (EPA refrigerant data). Hydrocarbon refrigerants such as R-290 are excluded from MVAC under SNAP because all flammable refrigerants other than HFC-152a and HFO-1234yf are listed as unacceptable (EPA SNAP MVAC).

Our reading is that each option buys something different. HFO-1234yf is the pragmatic default: A2L rather than highly flammable, compatible with conventional system pressures, and already the majority refrigerant in light-duty vehicles (EPA refrigerant data). R-744 offers strong cold-climate heating and a GWP of 1, but demands much higher system pressures, different components and deeper service competence. R-290 has good thermodynamic properties, but its flammability keeps it out of mainstream MVAC in the United States, so it remains a research and limited-market option. The right choice therefore depends on the market's regulation, the climate band and whether the platform is designed around a heat pump from the start.

NVH, lubrication and the high-voltage boundary

Three technical differences separate electric compressors from belt-driven units. The first is noise and vibration: an electric compressor's speed is electronically controlled and independent of engine speed, and at low vehicle speed there is no engine noise to mask motor whine and structure-borne vibration, so mounting isolation and housing design matter more than on engine-driven systems (our analysis). The second is lubrication: DENSO specifies a POE oil, ND-oil 11, for its electric-driven scroll compressors because the oil must also insulate the motor, which is cooled by the refrigerant-oil mixture (DENSO compressor oil). Moisture, wrong viscosity or mixed oil can compromise both wear protection and electrical insulation (our analysis). The third is the high-voltage boundary: testing a high-voltage electric compressor requires personal protective equipment, specific equipment and documented procedures, as MACS sets out in its training (MACS 609 training). Treat the compressor as part of the high-voltage system, not as a belt-driven accessory.

Market direction

The market context is not subtle. The IEA reports that electric car sales exceeded 17 million globally in 2024, a sales share above 20%, with China accounting for almost half of all car sales and more than 11 million electric cars sold there; 17.3 million electric cars were produced worldwide, 12.4 million of them in China, more than 70% of global production (IEA Global EV Outlook 2025). More vehicles means more electric compressors, more heat-pump platforms and more A2L systems entering the service fleet. The technology direction is toward integrated thermal modules, higher-voltage architectures, wider operating envelopes and refrigerants selected for cold-climate heating as much as for cooling.

What this means for compressor suppliers and installers

For suppliers, an electric compressor is a mechatronic assembly: motor, inverter, control electronics and scroll or piston mechanism have to be validated together, and the part number has to encode voltage class, refrigerant, oil and connector variant. Remanufacturing and repair are harder than for belt-driven units, and traceability and end-of-line testing matter more. For installers, the barrier is qualification: high-voltage safety training, insulated tooling, OEM de-energisation procedures and the discipline to use the specified oil and refrigerant. Distributors should expect EV-specific catalogue data, not a generic "fits all" listing. Model programmes include Toyota. Our industry news section tracks thermal-management developments.

Sources

  1. Global EV Outlook 2025 - Executive summary — International Energy Agency, accessed 2026-11-14
  2. Comparative analysis of thermal management systems in electric vehicles at extreme weather conditions — U.S. Department of Energy, OSTI (Argonne National Laboratory), accessed 2026-11-14
  3. Unitary Thermal Energy Management for Propulsion Range Augmentation (UTEMPRA) — U.S. Department of Energy, OSTI (NREL), accessed 2026-11-14
  4. Acceptable Refrigerants and their Impacts — U.S. Environmental Protection Agency, accessed 2026-11-14
  5. Substitutes in Motor Vehicle Air Conditioning — U.S. Environmental Protection Agency (SNAP), accessed 2026-11-14
  6. DENSO A/C compressor oil — DENSO Europe, accessed 2026-11-14
  7. Electrical Compressors — Sanden USA, accessed 2026-11-14
  8. EPA 609 Certification Tests and Training Materials — Mobile Air Climate Systems Association (MACS), accessed 2026-11-14

Every factual claim in this article is referenced to a public source; the full list is in the Sources section above.

Back to the newsroom Send an OE enquiry

More in Industry news

Enquiry Skype